HSE web guidance, updated 7 March 2025
Treating low-frequency compressor noise
Current. Last checked with HSE on 17 November 2026.
Guidance on HSE's website.
- Kind
- HSE web guidance, updated 7 March 2025
- HSE's date
- 7 March 2025
- Last checked
- 17 November 2026
The passage you were sent
What it says, in HSE's own words
The problem Large reciprocating air compressors producing high noise levels at low frequencies can be found in a wide range of manufacturing plants. In one company, two compressors operating at 370 rpm (revs per minute) drew air from the roof where the intake filters and other items of equipment needed regular attention. The A-weighted noise level near the air intakes was found to be 88 dB, determined almost entirely by energy in the 63 and 125 Hz frequency bands. Absorptive silencing was discounted as inefficient at these frequencies.
It would also have been impractical as the size of silencer necessary would have meant a need for additional roof support. The solution The solution was to install an intake silencer that could combine adequate low-frequency attenuation with low resistance to the air flow. A combined reactive and absorptive silencer was selected for each compressor. The silencers consisted of an all-welded outer tube with a cross-sectional area at least 15 times greater than that of the system side pipework.
Quoted from HSE. Open the original on hse.gov.uk
Key points
This case study covers the treatment of low-frequency noise from two large reciprocating air compressors in a manufacturing plant. Operating at 370 rpm (revs per minute), they produced an A-weighted noise level of 88 dB near the roof air intakes, mainly in the 63 and 125 Hz frequency bands. Absorptive silencing was discounted as inefficient at these frequencies and impractical because the required silencer would have needed additional roof support. A combined reactive and absorptive intake silencer was installed for each compressor. Its outer tube had a cross-sectional area at least 15 times greater than the system side pipework, with acoustically absorptive lining. The cost was About £2500 each. (1995). Overall noise reduction was 17 dB, with attenuation of 35 dB at 31.5 Hz.
Our summary of the document's own words. Check the original before you rely on it.
Machine-translated summary (Polish)
To studium przypadku dotyczy ograniczenia hałasu o niskiej częstotliwości z dwóch dużych tłokowych sprężarek powietrza w zakładzie produkcyjnym. Pracując z prędkością 370 rpm (obrotów na minutę), wytwarzały poziom hałasu ważony charakterystyką A wynoszący 88 dB w pobliżu wlotów powietrza na dachu, głównie w pasmach częstotliwości 63 i 125 Hz. Tłumienie absorpcyjne odrzucono jako nieefektywne przy tych częstotliwościach i niepraktyczne, ponieważ wymagany tłumik wymagałby dodatkowego podparcia dachu. Dla każdej sprężarki zainstalowano połączony reakcyjny i absorpcyjny tłumik wlotowy. Jego zewnętrzna rura miała pole przekroju co najmniej 15 razy większe niż boczne przewody rurowe systemu, a wewnątrz znajdowała się wykładzina pochłaniająca akustycznie. Koszt wynosił About £2500 each. (1995). Ogólna redukcja hałasu wyniosła 17 dB, a tłumienie 35 dB przy 31.5 Hz.
Machine-translated summary (Romanian)
Acest studiu de caz prezintă tratarea zgomotului de joasă frecvență provenit de la două compresoare mari de aer cu piston dintr-o fabrică de producție. Funcționând la 370 rpm (rotații pe minut), acestea produceau un nivel de zgomot ponderat A de 88 dB lângă prizele de aer de pe acoperiș, în principal în benzile de frecvență de 63 și 125 Hz. Atenuarea absorbantă a fost respinsă ca ineficientă la aceste frecvențe și nepractică, deoarece amortizorul necesar ar fi presupus un suport suplimentar pentru acoperiș. Pentru fiecare compresor a fost instalat un amortizor de admisie reactiv și absorbant combinat. Tubul exterior avea o suprafață a secțiunii transversale de cel puțin 15 ori mai mare decât conductele laterale ale sistemului, cu o căptușeală absorbantă acustic în interior. Costul a fost About £2500 each. (1995). Reducerea totală a zgomotului a fost de 17 dB, iar atenuarea de 35 dB la 31.5 Hz.
Check your RAMS against this document
Related guidance
- Reducing noise from screw compressors
- Active control of low-frequency, pure-tone noise
- Active/absorptive silencer for a rotary blower
- Reducing combustion noise by flow control
Tell me when HSE changes this
Tell me when HSE changes Treating low-frequency compressor noise. A line in the Monday email when HSE withdraws, replaces, moves or updates this document, and no email when it does not.
Contains public sector information published by the Health and Safety Executive and licensed under the Open Government Licence v3.0. KASQ is not affiliated with HSE.