KASQSite safety, in the crew's language
Start free

← All HSE guidance

HSE web guidance, updated 7 March 2025

Rubber damping landing chutes

Current. Last checked with HSE on 12 November 2026.

Guidance on HSE's website.

Kind
HSE web guidance, updated 7 March 2025
HSE's date
7 March 2025
Last checked
12 November 2026

What it says, in HSE's own words

The problem Damped landing chute Metal-on-metal impacts are a common and often disproportionately significant source of noise in many metal fabricating shops. One major motor manufacturer recently installed a cropping machine to automate the finishing of castings, previously carried out by operators using hand-held pneumatic tools. While the new equipment reduced noise exposure during the process itself, noise was still being generated by the unloading mechanism.
A mechanical arm lifted the casting out of the machine, rotated it clear and then dropped it from a height of about 1 m onto a metal chute. The impact of the components onto the chute created peak A-weighted levels of 100 dB. The solution A 5 mm layer of wear-resistant rubber matting was applied to the inside surfaces of the chute. The cost About £75 per square metre for material, plus installation. (1995) The result A noise reduction of about 15 dB. The treatment also protected the casting and chute from impact damage. Source Information and photograph supplied by Ford Motor Company Limited.

Quoted from HSE. Open the original on hse.gov.uk

Key points

This case study describes noise from metal-on-metal impacts in a metal fabricating shop. A mechanical arm lifted castings from a cropping machine, rotated them clear and dropped them from a height of about 1 m onto a metal chute, creating peak A-weighted levels of 100 dB. The solution was to apply a 5 mm layer of wear-resistant rubber matting to the chute’s inside surfaces. The cost was about £75 per square metre for material, plus installation (1995). The result was a noise reduction of about 15 dB, while also protecting the casting and chute from impact damage.

Our summary of the document's own words. Check the original before you rely on it.

Machine-translated summary (Polish)

To studium przypadku opisuje hałas powodowany uderzeniami metalu o metal w zakładzie obróbki metalu. Ramię mechaniczne podnosiło odlewy z maszyny do obcinania, obracało je, aby je odsunąć, i zrzucało z wysokości około 1 m na metalową rynnę, powodując szczytowe poziomy ważone A wynoszące 100 dB. Rozwiązaniem było nałożenie na wewnętrzne powierzchnie rynny warstwy odpornej na zużycie maty gumowej o grubości 5 mm. Koszt wynosił około £75 za metr kwadratowy materiału plus montaż (1995). Rezultatem było zmniejszenie hałasu o około 15 dB, a także ochrona odlewu i rynny przed uszkodzeniami wskutek uderzeń.

Machine-translated summary (Romanian)

Acest studiu de caz descrie zgomotul produs de impacturile metal pe metal într-un atelier de prelucrare a metalelor. Un braț mecanic ridica piesele turnate dintr-o mașină de debavurat, le rotea pentru a le îndepărta și apoi le lăsa să cadă de la o înălțime de aproximativ 1 m pe un jgheab metalic, creând niveluri maxime ponderate A de 100 dB. Soluția a fost aplicarea unui strat de covor de cauciuc rezistent la uzură, de 5 mm, pe suprafețele interioare ale jgheabului. Costul a fost de aproximativ £75 pe metru pătrat pentru material, plus instalarea (1995). Rezultatul a fost o reducere a zgomotului de aproximativ 15 dB, protejând totodată piesa turnată și jgheabul împotriva deteriorării prin impact.

Related guidance

Contains public sector information published by the Health and Safety Executive and licensed under the Open Government Licence v3.0. KASQ is not affiliated with HSE.