KASQSite safety, in the crew's language
Start free

← All HSE guidance

HSE web guidance, updated 3 April 2025

Employee killed whilst changing an electrode

Current. Last checked with HSE on 13 November 2026.

Guidance on HSE's website.

Kind
HSE web guidance, updated 3 April 2025
HSE's date
3 April 2025
Last checked
13 November 2026

What it says, in HSE's own words

An employee received a fatal electric shock whilst changing a welding rod during arc-welding work inside a metal silo. It was found that there was a voltage of no more than 86 Volts ac between the welding rod and the silo metalwork when no welding was taking place. There was an unsafe system of work in this hazardous environment. It was found during the investigation that the electrical equipment in use at the time of the accident was damaged but this was found not to be contributory to the accident.
The employer was prosecuted under the Health and Safety At Work etc. Act 1974, Section 2, Sub Section 1, and The Management of Health and Safety at Work Regulations 1992 (No 3) paragraph 1 and entered a guilty plea at magistrates court. They were later fined £250,000 at Crown Court. Comment This incident shows that even relatively low voltages can deliver a fatal electric shock, particularly where a person cannot easily escape the shock, and that arc welding equipment should be switched off when rods are being changed.

Quoted from HSE. Open the original on hse.gov.uk

Key points

An employee received a fatal electric shock while changing a welding rod during arc-welding work inside a metal silo. There was no more than 86 Volts ac between the welding rod and the silo metalwork when welding was not taking place, and an unsafe system of work was found in this hazardous environment. The electrical equipment was damaged but was not contributory to the accident. The employer was prosecuted under the Health and Safety At Work etc. Act 1974, Section 2, Sub Section 1, and The Management of Health and Safety at Work Regulations 1992 (No 3) paragraph 1, and was later fined £250,000. Arc welding equipment should be switched off when rods are changed. Electrical work in hazardous environments should not be carried out until a risk assessment has been done and control measures identified and implemented.

Our summary of the document's own words. Check the original before you rely on it.

Machine-translated summary (Polish)

Pracownik doznał śmiertelnego porażenia prądem podczas wymiany pręta spawalniczego w trakcie spawania łukowego wewnątrz metalowego silosu. Między prętem spawalniczym a metalowymi elementami silosu występowało nie więcej niż 86 Volts ac, gdy spawanie nie było prowadzone, a w tym niebezpiecznym środowisku stwierdzono niebezpieczny system pracy. Sprzęt elektryczny był uszkodzony, ale nie przyczynił się do wypadku. Pracodawca został postawiony w stan oskarżenia na podstawie Health and Safety At Work etc. Act 1974, Section 2, Sub Section 1, oraz The Management of Health and Safety at Work Regulations 1992 (No 3) paragraph 1, a następnie ukarany grzywną w wysokości £250,000. Sprzęt do spawania łukowego powinien być wyłączany podczas wymiany prętów. Prace elektryczne w niebezpiecznych środowiskach nie powinny być prowadzone, dopóki nie zostanie wykonana ocena ryzyka oraz nie zostaną określone i wdrożone środki kontroli.

Machine-translated summary (Romanian)

Un angajat a suferit un șoc electric fatal în timp ce schimba o tijă de sudură în timpul lucrărilor de sudare cu arc în interiorul unui siloz metalic. Între tija de sudură și componentele metalice ale silozului exista cel mult 86 Volts ac când sudarea nu avea loc, iar în acest mediu periculos a fost identificat un sistem de lucru nesigur. Echipamentul electric era deteriorat, dar nu a contribuit la accident. Angajatorul a fost urmărit penal în temeiul Health and Safety At Work etc. Act 1974, Section 2, Sub Section 1, și The Management of Health and Safety at Work Regulations 1992 (No 3) paragraph 1, iar ulterior a fost amendat cu £250,000. Echipamentul de sudare cu arc ar trebui oprit când tijele sunt schimbate. Lucrările electrice în medii periculoase nu ar trebui efectuate până când nu a fost realizată o evaluare a riscurilor și nu au fost identificate și implementate măsuri de control.

Related guidance

Contains public sector information published by the Health and Safety Executive and licensed under the Open Government Licence v3.0. KASQ is not affiliated with HSE.