KASQSite safety, in the crew's language
Start free

← All HSE guidance

HSE web guidance, updated 17 March 2025

Reciprocating compressor

Current. Last checked with HSE on 14 November 2026.

Guidance on HSE's website.

Kind
HSE web guidance, updated 17 March 2025
HSE's date
17 March 2025
Last checked
14 November 2026

What it says, in HSE's own words

The Problem A reciprocating air compressor had been in use for several years, both in a workshop and in mobile noise control demonstrations. Noise levels measured 94dB at 1m and clearly noise reduction was required. The Solution The noise reductions were all through maintenance. Initial work involved improving the valve seating. The old valves were observed to have a rough surface and to seal poorly to the casing. New valves were purchased and observed to be similarly rough. These were then dressed (polished) to achieve a much-improved seal.
An oil additive (molybdenum disulphide) was added to the lubricating oil to "smooth out" the surface finish in the cylinder, thus helping to cushion "piston slap". The Results The average reverberant noise level was reduced by 6dB to 87dB and the operators' noise exposures were reduced by 4dB. The Costs £150 (2005 rates). Information supplied by Worksafe, Department of Consumer and Employment Protection, Western Australia .

Quoted from HSE. Open the original on hse.gov.uk

Key points

This case study covers a reciprocating air compressor used for several years in a workshop and in mobile noise control demonstrations. Noise levels measured 94dB at 1m, so noise reduction was required. The reductions were achieved through maintenance. The valve seating was improved: old valves had a rough surface and sealed poorly to the casing, while new valves were dressed (polished) to achieve a much-improved seal. An oil additive (molybdenum disulphide) was added to the lubricating oil to “smooth out” the cylinder surface finish and help cushion “piston slap”. The average reverberant noise level fell by 6dB to 87dB, and operators’ noise exposures fell by 4dB. The cost was £150 (2005 rates).

Our summary of the document's own words. Check the original before you rely on it.

Machine-translated summary (Polish)

To studium przypadku dotyczy sprężarki powietrza tłokowej używanej przez kilka lat w warsztacie oraz podczas mobilnych demonstracji kontroli hałasu. Poziomy hałasu wynosiły 94dB przy 1m, dlatego wymagana była redukcja hałasu. Redukcję osiągnięto poprzez konserwację. Ulepszono osadzenie zaworów: stare zawory miały szorstką powierzchnię i słabo uszczelniały się względem obudowy, natomiast nowe zawory zostały obrobione (wypolerowane), aby uzyskać znacznie lepsze uszczelnienie. Do oleju smarującego dodano dodatek olejowy (dwusiarczek molibdenu), aby „wygładzić” wykończenie powierzchni cylindra i pomóc amortyzować „uderzenia tłoka”. Średni pogłosowy poziom hałasu zmniejszył się o 6dB do 87dB, a narażenie operatorów na hałas zmniejszyło się o 4dB. Koszt wyniósł £150 (stawki z 2005 r.).

Machine-translated summary (Romanian)

Acest studiu de caz se referă la un compresor de aer cu piston folosit timp de mai mulți ani într-un atelier și în demonstrații mobile de control al zgomotului. Nivelurile de zgomot măsurau 94dB la 1m, astfel că era necesară reducerea zgomotului. Reducerile au fost obținute prin întreținere. Așezarea supapelor a fost îmbunătățită: supapele vechi aveau o suprafață rugoasă și etanșau slab față de carcasă, iar supapele noi au fost prelucrate (lustruite) pentru a obține o etanșare mult îmbunătățită. În uleiul de lubrifiere a fost aditiv (disulfură de molibden) pentru a „netezi” finisarea suprafeței cilindrului și a ajuta la amortizarea „lovirii pistonului”. Nivelul mediu de zgomot reverberant a fost redus cu 6dB la 87dB, iar expunerile operatorilor la zgomot au fost reduse cu 4dB. Costul a fost £150 (tarifele din 2005).

Related guidance

Contains public sector information published by the Health and Safety Executive and licensed under the Open Government Licence v3.0. KASQ is not affiliated with HSE.