KASQSite safety, in the crew's language
Start free

← All HSE guidance

HSE web guidance, updated 7 November 2024

Construction dust: Cutting paving blocks kerbs and flags

Current. Last checked with HSE on 11 November 2026.

Guidance on HSE's website.

Kind
HSE web guidance, updated 7 November 2024
HSE's date
7 November 2024
Last checked
11 November 2026

What it says, in HSE's own words

Using cut-off saws on paving, blocks and kerbs can produce very high levels of silica containing dust. Effective control is necessary because this work is high risk. This page tells you how to control the risk and why. You also need to be aware of the general information on construction dust . What you must do Follow the Assess, Control and Review model . Pay particular attention to the following things: Assess Identify and assess : Using cut-off saws on paving, blocks or kerbs can produce very high levels of silica containing dust.
Anyone breathing in this dust cloud will be affected. Those using or very close to the cut-off saw will be particularly at risk. Follow the control steps below. Control Prevent : Think about limiting the risks before work starts by: using lower energy equipment like a block splitter limiting the number of cuts during design / lay-out getting material cut off-site and delivered Control : Even if you minimise some of the dust this way, you may still need to use a cut-off saw. Control the risk by: Water – use a hand-held cut-off saw with a water suppression attachment.

Quoted from HSE. Open the original on hse.gov.uk

Key points

Using cut-off saws on paving, blocks and kerbs can produce very high levels of silica containing dust, so effective control is necessary. The page sets out the Assess, Control and Review model. Before work starts, risks can be reduced by using lower energy equipment like a block splitter, limiting cuts during design / lay-out, or getting material cut off-site. Where a saw is used, controls include water suppression or on-tool extraction with an H or M class extraction unit, together with RPE with an assigned protection factor of 20, such as an FFP3 disposable mask or half mask with a P3 filter. Controls and RPE must be supervised, equipment maintained, and health surveillance may be needed. The Workplace Exposure Limit for silica is 0.1 mg/m 3 when averaged over 8 hours; dry cutting can produce peaks of up to 70 mg/m 3.

Our summary of the document's own words. Check the original before you rely on it.

Machine-translated summary (Polish)

Używanie pił przecinarek do nawierzchni, bloczków i krawężników może powodować bardzo wysokie poziomy pyłu zawierającego krzemionkę, dlatego konieczna jest skuteczna kontrola. Strona przedstawia model Oceń, Kontroluj i Przeglądaj. Przed rozpoczęciem pracy ryzyko można ograniczyć, używając sprzętu o niższej energii, takiego jak łuparka do bloczków, ograniczając liczbę cięć podczas projektowania / układania lub zlecając cięcie materiału poza miejscem pracy i dostarczenie go. Gdy używana jest piła, środki kontroli obejmują tłumienie wodą lub odciąg na narzędziu z jednostką odciągową klasy H lub M, wraz ze środkami ochrony dróg oddechowych o przypisanym współczynniku ochrony 20, takimi jak jednorazowa maska FFP3 lub półmaska z filtrem P3. Środki kontroli i RPE muszą być nadzorowane, sprzęt utrzymywany, a nadzór zdrowotny może być potrzebny. Dopuszczalna wartość narażenia zawodowego dla krzemionki wynosi 0.1 mg/m 3 jako średnia z 8 godzin; cięcie na sucho może powodować wartości szczytowe do 70 mg/m 3.

Machine-translated summary (Romanian)

Utilizarea ferăstraielor de tăiere pentru pavele, blocuri și borduri poate produce niveluri foarte ridicate de praf care conține silice, astfel încât este necesar un control eficient. Pagina prezintă modelul Evaluare, Control și Revizuire. Înainte de începerea lucrului, riscurile pot fi reduse prin folosirea unui echipament cu energie mai mică, precum un despicător de blocuri, prin limitarea numărului de tăieturi în timpul proiectării / amplasării sau prin tăierea materialului în afara șantierului și livrarea acestuia. Atunci când se folosește un ferăstrău, măsurile de control includ suprimarea cu apă sau extracția la unealtă cu o unitate de extracție de clasă H sau M, împreună cu echipament de protecție respiratorie cu un factor de protecție atribuit de 20, precum o mască de unică folosință FFP3 sau o semimască cu filtru P3. Măsurile de control și RPE trebuie supravegheate, echipamentul trebuie întreținut, iar supravegherea stării de sănătate poate fi necesară. Limita de expunere la locul de muncă pentru silice este 0.1 mg/m 3 calculată ca medie pe 8 ore; tăierea uscată poate produce expuneri de vârf de până la 70 mg/m 3.

Related guidance

Contains public sector information published by the Health and Safety Executive and licensed under the Open Government Licence v3.0. KASQ is not affiliated with HSE.