HSE web guidance, updated 12 November 2024
Construction dust: Sanding taped and covered plasterboard joints
Current. Last checked with HSE on 17 November 2026.
Guidance on HSE's website.
- Kind
- HSE web guidance, updated 12 November 2024
- HSE's date
- 12 November 2024
- Last checked
- 17 November 2026
The passage you were sent
What it says, in HSE's own words
Sanding taped and covered plasterboard joints can produce high levels of gypsum dust. This means effective control is necessary. This page tells you how to control the risk and why. You also need to be aware of the general information on construction dust . What you must do Follow the Assess, Control and Review model . Pay particular attention to the following things: Assess Identify and assess : Sanding plasterboard jointing can produce high levels of gypsum dust. Anyone breathing in the dust cloud will be affected.
Those doing the work will be particularly at risk. Follow the control steps below. Control Prevent : Think about limiting the risks before work starts by: using other methods to avoid the need for sanding. Control : If you need to sand plasterboard jointing, control the risk by: On-tool extraction – use specially adapted equipment with on-tool extraction . Select an H, M or L class extraction unit. Make sure the extraction flow rate is right for the work. Hose connections should be tight fitting and secure without obvious leaks.
Quoted from HSE. Open the original on hse.gov.uk
Key points
Sanding taped and covered plasterboard joints can produce high levels of gypsum dust, so effective control is necessary. The page sets out the Assess, Control and Review model. Before work starts, consider using other methods to avoid sanding. If sanding is needed, use specially adapted equipment with on-tool extraction and select an H, M or L class extraction unit; the extraction flow rate must suit the work, and hose connections should be tight fitting and secure without obvious leaks. Regularly check the hood, hoses and extraction unit, especially filters, extraction rates and warning devices. Someone competent should thoroughly examine dust extraction equipment and test its performance at least once every 14 months. Decide whether health surveillance is needed. The Workplace Exposure Limit for this fine respirable dust is 4.0 mg/m 3 when averaged over 8 hours. RPE is not needed when using extraction.
Our summary of the document's own words. Check the original before you rely on it.
Machine-translated summary (Polish)
Szlifowanie oklejonych i pokrytych masą spoin płyt gipsowo-kartonowych może wytwarzać wysokie stężenia pyłu gipsowego, dlatego konieczna jest skuteczna kontrola. Strona przedstawia model Oceń, Kontroluj i Przeanalizuj. Przed rozpoczęciem pracy należy rozważyć zastosowanie innych metod, aby uniknąć szlifowania. Jeśli szlifowanie jest potrzebne, należy używać specjalnie przystosowanego sprzętu z odciągiem na narzędziu i wybrać jednostkę odciągową klasy H, M lub L; natężenie przepływu odciągu musi być odpowiednie do pracy, a połączenia węży powinny być szczelne i bezpieczne, bez widocznych wycieków. Należy regularnie sprawdzać osłonę, węże i jednostkę odciągową, zwłaszcza filtry, wydajność odciągu i urządzenia ostrzegawcze. Osoba kompetentna powinna dokładnie zbadać sprzęt do odciągania pyłu i sprawdzić jego działanie co najmniej raz na 14 miesięcy. Należy zdecydować, czy potrzebny jest program nadzoru zdrowotnego. Wartość dopuszczalnego narażenia zawodowego dla tego drobnego pyłu respirabilnego wynosi 4.0 mg/m 3, uśrednione w ciągu 8 godzin. Przy stosowaniu odciągu RPE nie jest potrzebne.
Machine-translated summary (Romanian)
Șlefuirea îmbinărilor de plăci de gips-carton lipite și acoperite poate produce niveluri ridicate de praf de gips, astfel că este necesar un control eficient. Pagina prezintă modelul Evaluează, Controlează și Revizuiește. Înainte de începerea lucrului, luați în considerare utilizarea altor metode pentru a evita șlefuirea. Dacă șlefuirea este necesară, utilizați echipamente special adaptate cu extracție la unealtă și selectați o unitate de extracție de clasa H, M sau L; debitul de extracție trebuie să fie potrivit pentru lucrare, iar conexiunile furtunurilor ar trebui să fie bine fixate și sigure, fără scurgeri evidente. Verificați regulat apărătoarea, furtunurile și unitatea de extracție, acordând o atenție deosebită filtrelor, debitelor de extracție și dispozitivelor de avertizare. O persoană competentă ar trebui să examineze temeinic orice echipament de extracție a prafului și să-i testeze performanța cel puțin o dată la 14 luni. Decideți dacă este necesar un program de supraveghere a sănătății. Limita de expunere la locul de muncă pentru acest praf respirabil fin este 4.0 mg/m 3 când este calculată ca medie pe 8 ore. EPR nu este necesar atunci când se utilizează extracția.
Check your RAMS against this document
Related guidance
- Construction dust: Cutting and sanding wood
- Construction dust: Scabbling or grinding
- Construction dust
- Construction hazardous substances: Lead
Tell me when HSE changes this
Tell me when HSE changes Construction dust: Sanding taped and covered plasterboard joints. A line in the Monday email when HSE withdraws, replaces, moves or updates this document, and no email when it does not.
Contains public sector information published by the Health and Safety Executive and licensed under the Open Government Licence v3.0. KASQ is not affiliated with HSE.