HSE publication CIS54
Dust control on cut-off saws used for stone or concrete cutting
Current. Last checked with HSE on 16 November 2026.
- Kind
- HSE publication CIS54
- Last checked
- 16 November 2026
The passage you were sent
What it says, in HSE's own words
Construction Information Sheet No 54 (Revision 1) Dust control on cut-off saws used for stone or concrete cutting HSE information sheet Introduction This information sheet describes dust control systems used with cut-off saws. Two well-established dust control techniques, wet dust suppression and local exhaust ventilation (LEV), are described. Cut-off saws (variously known as disc cutters, skill saws, Stihl saws, con saws or ‘whizzers’) are widely used in the construction industry.
They are normally fitted with 9- or 12-inch (205- or 230-mm) diameter blades, depending on the make and model. There are two blade types: diamond tip or resin- bonded abrasive wheel. Cutting paving slabs, kerb stones or other concrete or stone products produces enormous amounts of dust. This dust will contain some very fine dust called respirable crystalline silica (RCS). Exposure to RCS dust can cause serious health problems which may eventually prove to be fatal.
Quoted from HSE. Open the original on hse.gov.uk
Key points
This information sheet is for people using hand-held cut-off saws in construction to cut stone or concrete. It describes wet dust suppression and local exhaust ventilation (LEV) and the risks from respirable crystalline silica (RCS), including serious lung disease. It states that the Control of Substances Hazardous to Health Regulations 2002 (as amended) require effective, reliable controls to minimise RCS escape and spread, with suitable respiratory protective equipment (RPE) where exposure cannot otherwise be adequately controlled, and that exposure must be below 0.1 mg/m3 over an 8-hour Time Weighted Average (TWA). Controls include water flow of about 0.5 litres per minute, LEV with an H Class 13 HEPA filter to EN60335–1, RPE with an assigned protection factor of at least 20, training and face fit testing, equipment maintenance, and controls for other risks.
Our summary of the document's own words. Check the original before you rely on it.
Machine-translated summary (Polish)
Niniejsza karta informacyjna jest przeznaczona dla osób używających ręcznych przecinarek tarczowych w budownictwie do cięcia kamienia lub betonu. Opisuje tłumienie pyłu metodą mokrą i wentylację wyciągową miejscową (LEV) oraz zagrożenia związane z respirabilną krzemionką krystaliczną (RCS), w tym poważne choroby płuc. Stwierdza, że Control of Substances Hazardous to Health Regulations 2002 (as amended) wymagają skutecznych i niezawodnych środków kontroli w celu zminimalizowania wydostawania się i rozprzestrzeniania RCS, a także odpowiedniego sprzętu ochrony dróg oddechowych (RPE), gdy narażenia nie można odpowiednio ograniczyć w inny sposób, oraz że narażenie musi być niższe niż 0.1 mg/m3 w ciągu 8-godzinnej średniej ważonej w czasie (TWA). Środki kontroli obejmują przepływ wody około 0.5 litra na minutę, LEV z filtrem H Class 13 HEPA zgodnym z EN60335–1, RPE o przypisanym współczynniku ochrony wynoszącym co najmniej 20, szkolenie i test dopasowania do twarzy, konserwację sprzętu oraz kontrolowanie innych zagrożeń.
Machine-translated summary (Romanian)
Această fișă informativă se adresează persoanelor care folosesc ferăstraie de tăiere portabile în construcții pentru tăierea pietrei sau betonului. Ea descrie suprimarea umedă a prafului și ventilația locală prin aspirație (LEV), precum și riscurile asociate cu silicea cristalină respirabilă (RCS), inclusiv bolile pulmonare grave. Precizează că Control of Substances Hazardous to Health Regulations 2002 (as amended) impun măsuri de control eficiente și fiabile pentru a minimiza degajarea și răspândirea RCS, precum și echipament adecvat de protecție respiratorie (RPE) atunci când expunerea nu poate fi controlată în mod adecvat în alt mod, iar expunerea trebuie menținută sub 0.1 mg/m3 pe o medie ponderată în timp (TWA) de 8 ore. Măsurile de control includ un debit de apă de aproximativ 0.5 litri pe minut, LEV cu un filtru H Class 13 HEPA conform EN60335–1, RPE cu un factor de protecție atribuit de cel puțin 20, instruire și testarea etanșeității pe față, întreținerea echipamentului și controlul altor riscuri.
Check your RAMS against this document
Tell me when HSE changes this
Tell me when HSE changes Dust control on cut-off saws used for stone or concrete cutting. A line in the Monday email when HSE withdraws, replaces, moves or updates this document, and no email when it does not.
Contains public sector information published by the Health and Safety Executive and licensed under the Open Government Licence v3.0. KASQ is not affiliated with HSE.